USED MITCHELL PP-453, 150,000 LB SINGLE DIE HYD PUSH POINTER (14272

150,000 lb MITCHELL PP-453 SINGLE DIE HYDRAULIC TUBE PUSH POINTER (14272)

150,000 lb MITCHELL SINGLE DIE HYDRAULIC PUSH POINTER
STOCK # 14272

Designed And Built By: GEORGE A. MITCHELL CO.

Serial No. PP-453
Tube Material: ZR-2 TUBING, COPPER OR ALUMINUM
Tube Size Range: 5" MAX OD (per Mfg. Specs)
2" MIN OD (per Mfg. Specs)
3/8" MAX WALL

Capacities:.
Die Advance - Rated: 150,000 LBS AT 1949 PSI
Die Advance - Maximum: 192,400 LBS AT 2500 PSI
Clamp Holding: ADJUSTABLE UP TO MAX
475,000 LBS AT 5000 PSI
Speeds:
Die Advance : 79.6 IPM AT 2000 PSI
Die Return: 172.0 IPM AT 1000 PSI
Clamp Advance: 68.1 IPM @ 1000 PSI
Clamp Return: 114.3 IPM AT 1000 PSI
Die Holder: SINGLE "U" SHAPED
OPEN TOP CAVITY TO
ACCEPT ROUND CASE
POINTING DIES

Cycles:
Automatic One Push
Semi-Automatic Two Push With Manual Die Change
Point Length Adjustable To 14" Max. (Parallel Section)
Method of Keeping
Point Straight: Patented Air Cylinder
Operated Conical Point Follower
Die Crosshead Travel. 18"
Jaw Size - Per Half . 3-7/8" Tk. x 6-3/8" Wide x 18" Lg.
Hardened Steel For 3.75" O.D. Tube
Method of Changing Dies: Manual - Approx 40 lbs
For 8" OD Die
Method of Changing Jaws: Manual - Approx 65 lbs
Per Half
Max. Opening Between Jaws: 3-3/4"
Clamp Mechanism: Direct Acting Hydraulic Cylinder

Hydraulic Pumps:
Clamp & Push Vickers Vane Type
26.5 GPM at 2000 PSI at 1200 RPM
Clamp Sealing: Oilgear Piston Type
1.72 GPM at 5000 PSI at 1200 RPM
Hydraulic Reservoir: 150 Gallon Capacity
Hydraulic Fluid: Petroleum Oil
150-315 SUS at 100 Degree F

Hydraulic Pump Drive Motor: 50HP, 1200 RPM, 460 V.,
3 Ph., 60 Hz., Double Shaft,
TEFC, Fr. 365T
Hydraulic Pump Drive
Motor Starter: Size 3, Full Voltage Combination
With Fused Disconnect In NEMA 12 Enclosure

Method of Lubricating Tube End
To Be Pointed: Manual
Oil Cooler: Water Type With Automatic
Temperature Control
Main Power Supply: 460 V, 3 Ph, 60 Hz
Control Power: 120 Volt, Single Phase
From Transformer Supplied
Control Logic: Programmable Control

IDLER ROLLER LOAD/UNLOAD STAND

Number of Support Rolls: 12 on Approx. 60" Centers
Type of Roll : "V" Shaped Urethane
Roll Idle Rotation.: 1-1/2" Anti-friction Bearing
on Each Side of Roll
Roll Support & Vertical Adjustment: Individual Pivot
Mounting of Each Roll With Interconnecting
Pull Bar Adjusted by Manual
Handwheel on Screw Jack
Vertical Adjustment Range
Of Rolls: To Accommodate From
2" Min. to 5" Max. O.D. Tubes

Estimated Equipment Shipping Weights:
Pointer: 15,000 Lbs
Hydraulic Pumping Unit: 3,000 Lbs
Load/Unload Stand: 7,000 Lbs

Tube Gripper Jaws Furnished:
ONE ( 1) PAIR SINGLE SIDED: 3.675"
Dies Furnished: 3.375" & 3.100"

**PLEASE NOTE MANUFACTURERS SPECIFICATIONS**
**Temporary Specifications Subject to Revisions**
**PRICE QUOTED AS IS WHERE IS SUBJECT TO PRIOR SALE**
**ALL SPECIFICATIONS ARE SUBJECT TO BUYER VERIFICATION**