USED 1978 TOYODA GOP 10-30

1978 Toyoda GOP 10-30 Universal Cylindrical Grinder - 12" Centers, 8" Swing.

SWING................................................8"
DISTANCE BETWEEN CENTERS.............................12"
CENTER HEIGHT........................................4"
MAX. GRINDING DIAMETER...............................2.36"
MAX. LOAD BETWEEN CENTERS............................44 LBS
WHEELHEAD:
TOTAL STROKE.........................................6.87"
TOTAL STROKE THROUGH MICROMETRIC MECHANISM...........6"
HYDRAULIC RAPID APPROACH AND WITHDRAWL STROKE........1"
AUTOMATIC FEED APPROACH STROKE.......................0.02"
AUTOMATIC INFEED AT THE END OF THE TABLE TRAVERSE....0.00005~0.0012"
INFEED PER HANDWHEEEL TURN...........................0.025"
GRADUATION OF THE WHEELHEAD HANDWHEEL................0.0001"
WHEEL (OUTSIDE DIA.x WIDTH x INDSIDE DIA.)...........14" 1.5" X 5"
REVOLUTIONS PER MINUTE...............................1,800;2,100;2,500 R.P.M.
NUMBER OF SPEED CHANGE (BY PULLEY CHANGE)............3
TABLE:
MINIMUM AUTOMATIC RECIPROCATING STROKE...............0.08"~0.12"
SPEED RANGE..........................................2"~106"/MIN
SWIVELLING ANGLE.....................................12 DEGREES, 7 DEGREES
HANDLE FEED AMOUNT (PER TURN)........................1"
WORKHEAD:
CENTER...............................................MT NO. 2
NUMBER OF SPEED CHANGE...............................4 (STANDARD) STEPLES (SPECIAL)
SPINDLE REVOLUTIONS..................................500 (STANDARD) 30~500 (SPECIAL)
LIVE OR DEAD SPIONDLE................................LIVE
SPINDLE HOLE DIAMETER................................0.6"
FOOTSTOCK:
CENTER...............................................MT NO.2
MAX. WITHDRAWL OF CENTER.............................0.8"
TIMER ADJUSTING RANGE................................0~30 SEC
MOTORS:
FOR WHEELHEAD........................................3 HP
FOR WORKHEAD.........................................1/4 HP
FOR HYDRAULIC PUMP...................................1/2 HP
FOR WHEEL SPINDLE BEARINGS PUMP......................1/3 HP
FOR COOLANT PUMP.....................................1/3 HP
TANK CAPACITY:
FOR HYDRAULIC MECHANISM..............................7.9 GAL.
FOR WHEEL SPINDLE BEARINGS...........................1.6 GAL.
FOR COOLANT..........................................15.8 GAL.
FLOOR SPACE REQUIRED.................................89.5" x 64" x 51.5"
NET WEIGHT...........................................3,970 LBS

WHEEL WA60KmV (14x1.5x5")
WHEEL WA60KmV (12x1.5x5")
WHEEL SLEEVE
BALACNING MANDERL
WHEELHEAD MOTOR PULLEYS
V-BELT (A44x3, M22x1, M19x2)
CARBIDE- TIPPED CENTERS (MT NO. 2)
TABLE DIAMOND HOLDER (WITHOUT DIAMOND)
BEARING OIL FILTER
SLIDE LUBRICATN FILTER
PRESSURE GAUGE
FOR WHEEL SPINDLE BEARINGS
FOR HYDRAULIC SYSTEM
FOR LUBRICATING OIL (2)
SCREW JACK (3)
DIAL INDICATOR ON TABLE (0.001") PER GRADUATION
HYDRAULIC TANK
COOLANT SUPPLY EQUIPMENT (WITH ELECTRIC PUMP)
STANDARD ELECTRICAL EQUIPMENT (POWER CIRCUIT 200v, CONTROL CIRCUIT 100V)
STANDARD TOOLS
INSTRUCTION MANUAL
WHEELHEAD AUTOMATIC INFEED DEVICE
WHEELHEAD AUTOMATIC INTERMITTENT INFEED DEVICE
TIMER (0~30 SEC)
WHEELHEAD OF NON-SWIVELLING TYPE
WORKHEAD OF NON-SWIVELLING TYPE
SLINGING HOOK FOR WHEEL

**BUYER RESPONSIBLE FOR VERIFYING SPECIFICATIONS & OPTIONS**