The Vision of Precision
• 10 H.P.
• 2” Blade
• Heavy-Duty
• Hydraulic
• Metal Cutting
FEATURES
• Saw Frame
- The saw frame is canted at a 6.5-degree angle for faster cutting of structural and other flat materials. The heavy-duty saw frame rides up and down a linear way guide system.
• Miter Cutting
- The WS2543M model has a saw base that swivels to 45 degrees one direction and 60 degrees the other, for miter cutting. A ½ hp (400 W.) motor turns the machine base and the degree of angle is read out on a LED DISPLAY.
• Speed Range
- 98-361 FPM (30-110m/min.). Infinitely variable through a frequency inverter system and a heavy-duty Worm Gear
Transmission. The broad speed range allows for optimum cutting of a large spectrum of materials. An Electric Tachometer assures accurate speed settings.
• Hydraulic Down Feed
- Feed rate and down pressure can be controlled for fast, accurate cutting. Setup is made easy through the color-coded dial allowing the operator to select the optimum setting for the type of material being cut.
• Blade Guides
- A combination of roller bearing and hydraulically actuated carbide blade guides assure the blade is held taut for fast, accurate cuts. The cast iron Movable Guide Arm is positioned through a Hydraulic Cylinder, then is Hydraulically Locked in position.
• Fast Approach
- Work height is manually set allowing the head to raise just enough to clear the workpiece, reducing cycle time
and allowing for faster cutting performance.
• Chip Brush
- An Independent Motor drives the blade cleaning Chip Brush to assure complete removal of chips from each gullet of
the blade, providing optimum cutting performance and enhanced blade life.
• Vise Jaw
- Full Stroking Vise Jaw and a Vertical Clamp Device assure the workpiece is secure and eliminates excessive vibration during the cut providing better blade life and cleaner cuts. Minimum Clamping Capacity is 7.5” (190mm) width.
• Controls
- An Independent Electric Cabinet and Control Panel allow the operator to position the controls for optimum viewing of the cutting area. A PLC controls all electrical and hydraulic functions.
Cutting Capacity:
Round (Diameter) at 90° 28″ 711 mm
Only WS2543M Round (Diameter) at 45° 28″ 711 mm
Only WS2543M Round (Diameter) at 60° 25.6″ 650 mm
Rectangle (W x H) 90° 44″ x 27″ 1117.6 x 685.8 mm
Only WS2543M Rectangle (W x H) at 45° 25.6″ x 27″ 650 x 685.8 mm
Only WS2543M Rectangle (W x H) at 60° 15.7″ x 25.6″ 400 x 650 mm
Work Load Capacity 11,020 lbs 4,998 kg
Saw Blade:
Blade Size (L x T x W) 28’6-1/2″ x 0.063″ x 2″ 8700 x 1.6 x 54 mm
Blade Speed 98-361 ft./min, by Inverter 30-110 m/min, by Inverter
Tension Control Hydraulic
Blade Control:
Top Limit Setting Automatic Setting with Fast Approach Feeler
Cutting Control Hydraulic Pressure & Flow Control Valve
Vise Operation:
Type Split Vises and Vertical Clamp Device
Control Hydraulic Full-Stroke Cylinder
Motors:
Saw Blade 10 HP 7.5 kW
Hydraulic Pump 3 HP 2.2 kW
Cutting Fluid Pump 1/4 HP 0.18 kW
Only WS2543M
Roll Motor 1.5 HP 1.1 kW
Only WS2543M
Table Rotation 1/2 HP 0.4 kW
Power Requirement:
Power Supply Voltage AC230V±10%, 3 PH, 60 Hz, Voltage must be specified when ordering
Power Requirement
Cutting Fluid Tank Capacity 47.5 gal 215 liters
Hydraulic
Tank Capacity
19.8 gal (WS2543M) 90 liters (WS2543M)
21 gal (W2543M) 95 liters (W2543M)
Pressure Setting
1067 psi (WS2543M) 7.35 MPa (75 kgf/cm2) (WS2543M)
996 psi (W2543M) 6.86 MPa (70 kgf/cm2) (W2543M)
Chip Disposal Chip Conveyor
Machine Dimensions (W x L x H) 179″ x 89.4″ x 101″ 4550 x 2270 x 2560 mm
Table Height 32’ – 33’ 810 – 850 mm
Machine Weight
11,880 lbs (WS2543M) 5,400 kg (WS2543M)
9,500 lbs (W2543M) 4,300 kg (W2543M)
